One of the most affordable and convenient methods for small-scale asphalt mending projects is to use a cold patch mix. Many property owners will tell you that this approach saves money, Black Top Pavement in Randburg and can reduce the amount of labor required for the job, making it a great solution for small holes in parking lots, walkways, streets, and driveways. However, the process of cold asphalt patching can be accelerated with the right application techniques, saving property owners some time too! Customers, clients, guests, and occupants can use the pavement in the same day!
Continue reading to learn some great tips on how you can shorten the amount of time it takes for the cold patch asphalt mix to harden, and drastically cut down on turnaround time, from project start to finish.
Ease of Use
The primary reason why this product is the go-to choice for small hole repairs in asphalt pavements is the ease of installation. There is no long, extended process of preparing or mixing materials. Instead, the air does most of the work. You simply pour the mix directly into the hole, compact it with simple manual tools (metal tamper or piece of lumber), and leave it to air dry. The mix turns into a permanent surface patch after extended contact with air.
The drying process, also known as curing, is very important to establishing a solid, stable surface that lasts a long time. If you want a permanent repair for your asphalt, you need to make sure the entire process is done correctly. If you want to speed up the curing stage of your pavement repair project, you can try a few recommended tips.
You can use gravel to create a more dense space within the hole, which may help to establish lasting strength. Just fill the hole with gravel, little by little, while using your compacting tools to compress the gravel with each layer. Do not fill the hole all the way to the top; be sure to leave 2 inches of space below the surface line for your cold patch mix.
Pouring Your Mix
As you pour your mix, exceed the surface line by half an inch. This means that your mix should go over the top of the hole by a ½ inch. Then use your compacting tools to compress your material down until it is properly flattened. You may need to repeat this step two or three times to get a proper fill.
Asphalt cold patch mix cures by having contact with air. You can speed up the drying process by using hair dryers or commercial paint dryers. If you are going to use a hair dryer, you will need to manually operate it in a steady, sweeping motion to ensure even curing. The material is near dry when you cannot easily press into the surface with your hand.
Large-Scale Pavement Repair
For large-scale pavement repair jobs, you need a professional paving company. They have the training, equipment, and resources to provide dependable work in a convenient time frame. Be sure to choose a company that is licensed, bonded, and insured, and retains decades of experience in the road construction industry.
Black Top Pavement in Randburg ?
There are several things you will want to keep in mind when making asphalt repairs. First, consider what has caused the asphalt to fail. The two most common reasons for asphalt failure are ultraviolet rays and water damage. Ultraviolet rays break down the asphaltic material in asphalt, resulting in cracks. The water penetrates the asphalt through the cracks and allows the sub base material to become saturated and washed out. When the base material is washed out from underneath the asphalt, it allows the asphalt to further fail and eventually turn into a pothole. Once a pothole is created, the base underneath the pothole now needs to be addressed before paying over it again.
To start, the base material that has been saturated must be removed. Normally the size of equipment necessary for excavation depends on the size of the troubled area. The material can be removed with anything from a small skid steer to large excavation equipment. Once the area has been evaluated and the material has been removed, the perimeter of the troubled area will need to be saw cut. Saw cuts are made first by popping chalk lines using a caulk box. These chalk lines are followed with the saw insuring straight cuts around the perimeter of the troubled area. By executing these steps in the beginning your end product will be stronger and more attractive.
After the saw cuts are made around the perimeter, neatly clean out asphalt and materials in the affected area. The area needs to be clean and free of debris. All wet materials should be removed from the area to insure a proper foundation for the new base material. After removing the wet materials, replace the area with a new compactable material, such as stone or crush and run. Depending on the size and depth of the excavation, it may be necessary to compact the new material in lifts as it is put into place. After placing the proper compaction of the base material, a tack coat should be applied. This tack coat will insure adhesion between the base material and the new paving.
Finally, you are ready for paving. The new asphalt paving material should be applied at the same depth as the existing asphalt. To ensure the area matches the elevation of the existing asphalt,you will need to make sure the new asphalt has been compacted with a vibratory roller compactor. Last but not least, clean up the entire work area with a blower and remove all excess debris.
Asphalt - To Seal or Not to Seal, That Is the Question
There are several reasons why many commercial property owners are paving their driveways with asphalt rather than concrete. Asphalt pavement comes with many benefits and advantages; especially when it comes to maintenance and repair. Asphalt is much more economical than concrete for this reason and more. On top of its flexibility and easy maintenance aspects, it typically costs less than concrete materials at most hardware and construction stores.
Although concrete paving can last up to 15 or 20 years without needing repairs, asphalt is still a trendier choice for most residential and commercial properties for a number of reasons. Continue reading to catch up on some important information about asphalt paving and why it is more popular than concrete these days.
Asphalt Pavement for Driveways
As mentioned before, concrete can last up to fifteen or twenty years without needing repairs; while asphalt paving may eventually require some upkeep after about five to seven years. There are several reasons why asphalt pavement can weaken or deteriorate. For example, elemental conditions, over-exposure, negligence, cars, and the surrounding natural environment call all have an effect on asphalt pavements. The following influences are common contributors to asphalt damage, pot holes, and wear and tear:
- Heavy Trucks, Cars, and Loads
- Substantial Water Saturation
- Constant Exposure to Moisture
- Harsh Storms
- Overgrown Tree Roots
- Poor Foundation
- Tectonic Plates
- And More
You can purchase asphalt fillers and pot hole repair kits at local hardware and home good stores; however, it is highly recommended to seek out professional assistance from a licensed and experienced asphalt paving engineer. They can give you the best advice on asphalt maintenance and repair. If you do decide to repair asphalt driveway damages on your own, you can still ask a retail clerk at the store for extra instructions or advice. They too should know plenty of information about the product they are selling.
Black Top Pavement Randburg