For other uses, see Asphalt (disambiguation). Note: The terms bitumen and asphalt are mostly interchangeable, Residential Asphalt Driveway Contractors in Bryanston except where asphalt is used as a shorthand for asphalt concrete. Natural bitumen from the Dead Sea Refined asphalt The University of Queensland pitch drop experiment, demonstrating the viscosity of asphalt
Asphalt (/ˈæsˌfɔːlt, -ˌfɑːlt/), also known as bitumen (UK English: /ˈbɪtʃəmən, ˈbɪtjʊmən/, US English: /bɪˈt(j)uːmən, baɪˈt(j)uːmən/) is a sticky, black, and highly viscous liquid or semi-solid form of petroleum. It may be found in natural deposits or may be a refined product, and is classed as a pitch. Before the 20th century, the term asphaltum was also used.
The primary use (70%) of asphalt Asphalt Companies Near My Location is in road construction, where it is used as the glue or binder mixed with aggregate particles to create asphalt concrete. Its other main uses are for bituminous waterproofing products, including production of roofing felt and for sealing flat roofs.
The terms “asphalt” and “bitumen” are often used interchangeably to mean both natural and manufactured forms of the substance. In American English, “asphalt” (or “asphalt cement”) is commonly used for a refined residue from the distillation process of selected crude oils. Outside the United States, the product is often called “bitumen”, and geologists worldwide often prefer the term for the naturally occurring variety. Common colloquial usage often refers to various forms of asphalt as “tar”, as in the name of the La Brea Tar Pits.
Naturally occurring asphalt is sometimes specified by the term “crude bitumen”. Residential Asphalt Driveway Contractors Its viscosity is similar to that of cold molasses while the material obtained from the fractional distillation of crude oil boiling at 525 °C (977 °F) is sometimes referred to as “refined bitumen”. The Canadian province of Alberta has most of the world’s reserves of natural asphalt in the Athabasca oil sands, which cover 142,000 square kilometres (55,000 sq mi), an area larger than England.
The word “asphalt” is derived from the late Middle English, in turn from French asphalte, based on Late Latin asphalton, asphaltum, which is the latinisation of the Greek ἄσφαλτος (ásphaltos, ásphalton), a word meaning “asphalt/bitumen/pitch” which perhaps derives from ἀ-, “without” and σφάλλω (sfallō), “make fall”. Driveway Pavers the first use of asphalt by the ancients was in the nature of a cement for securing or joining together various objects, and it thus seems likely that the name itself was expressive of this application. Specifically, Herodotus mentioned that bitumen was brought to Babylon to build its gigantic fortification wall. From the Greek, the word passed into late Latin, and thence into French (asphalte) and English (“asphaltum” and “asphalt”). In French, the term asphalte is used for naturally occurring asphalt-soaked limestone deposits, and for specialised manufactured products with fewer voids or greater bitumen content than the “asphaltic concrete” used to pave roads.
The expression “bitumen” originated in the Sanskrit words jatu, meaning “pitch”, and jatu-krit, meaning “pitch creating” or “pitch producing” (referring to coniferous or resinous trees). The Latin equivalent is claimed by some to be originally gwitu-men (pertaining to pitch), and by others, pixtumens (exuding or bubbling pitch), which was subsequently shortened to bitumen, thence passing via French into English. From the same root is derived the Anglo-Saxon word cwidu (mastix), the German word Kitt (cement or mastic) and the old Norse word kvada.
In British English, “bitumen” is used instead of “asphalt”. The word “asphalt” is instead used to refer to asphalt concrete, a mixture of construction aggregate and asphalt itself (also called “tarmac” in common parlance). Bitumen mixed with clay was usually called “asphaltum”, but the term is less commonly used today.
In Australian English, “bitumen” is often used as the generic term for road surfaces.
In American English, “asphalt” is equivalent to the British “bitumen”. However, “asphalt” is also commonly used as a shortened form of “asphalt concrete” (therefore equivalent to the British “asphalt” or “tarmac”).
In Canadian English, the word “bitumen” is used to refer to the vast Canadian deposits of extremely heavy crude oil, while “asphalt” is used for the oil refinery product. Diluted bitumen (diluted with naphtha to make it flow in pipelines) is known as “dilbit” in the Canadian petroleum industry, while bitumen “upgraded” to synthetic crude oil is known as “syncrude”, and syncrude blended with bitumen is called “synbit”.
“Bitumen” is still the preferred geological term for naturally occurring deposits of the solid or semi-solid form of petroleum. “Bituminous rock” is a form of sandstone impregnated with bitumen. The tar sands of Alberta, Canada are a similar material.
Neither of the terms “asphalt” or “bitumen” should be confused with tar or coal tars.[further explanation needed]
See also: Asphaltene
The components of asphalt include four main classes of compounds:
The naphthene aromatics and polar aromatics are typically the majority components. Most natural bitumens also contain organosulfur compounds, resulting in an overall sulfur content of up to 4%. Nickel and vanadium are found at <10 parts per million, as is typical of some petroleum.
The substance is soluble in carbon disulfide. It is commonly modelled as a colloid, with asphaltenes as the dispersed phase and maltenes as the continuous phase. “It is almost impossible to separate and identify all the different molecules of asphalt, because the number of molecules with different chemical structure is extremely large”.
Asphalt may be confused with coal tar, which is a visually similar black, thermoplastic material produced by the destructive distillation of coal. During the early and mid-20th century, when town gas was produced, coal tar was a readily available byproduct and extensively used as the binder for road aggregates. The addition of coal tar to macadam roads led to the word “tarmac”, which is now used in common parlance to refer to road-making materials. However, since the 1970s, when natural gas succeeded town gas, asphalt has completely overtaken the use of coal tar in these applications. Other examples of this confusion include the La Brea Tar Pits and the Canadian oil sands, both of which actually contain natural bitumen rather than tar. “Pitch” is another term sometimes informally used at times to refer to asphalt, as in Pitch Lake.
Bituminous outcrop of the Puy de la Poix, Clermont-Ferrand, France
The majority of asphalt used commercially is obtained from petroleum. Nonetheless, large amounts of asphalt occur in concentrated form in nature. Naturally occurring deposits of bitumen are formed from the remains of ancient, microscopic algae (diatoms) and other once-living things. These remains were deposited in the mud on the bottom of the ocean or lake where the organisms lived. Under the heat (above 50 °C) and pressure of burial deep in the earth, the remains were transformed into materials such as bitumen, kerogen, or petroleum.
Natural deposits of bitumen include lakes such as the Pitch Lake in Trinidad and Tobago and Lake Bermudez in Venezuela. Natural seeps occur in the La Brea Tar Pits and in the Dead Sea.
Bitumen also occurs in unconsolidated sandstones known as “oil sands” in Alberta, Canada, and the similar “tar sands” in Utah, US. The Canadian province of Alberta has most of the world’s reserves, in three huge deposits covering 142,000 square kilometres (55,000 sq mi), an area larger than England or New York state. These bituminous sands contain 166 billion barrels (26.4×10^9 m3) of commercially established oil reserves, giving Canada the third largest oil reserves in the world. Although historically it was used without refining to pave roads, nearly all of the output is now used as raw material for oil refineries in Canada and the United States.
The world’s largest deposit of natural bitumen, known as the Athabasca oil sands, is located in the McMurray Formation of Northern Alberta. This formation is from the early Cretaceous, and is composed of numerous lenses of oil-bearing sand with up to 20% oil. Isotopic studies show the oil deposits to be about 110 million years old. Two smaller but still very large formations occur in the Peace River oil sands and the Cold Lake oil sands, to the west and southeast of the Athabasca oil sands, respectively. Of the Alberta deposits, only parts of the Athabasca oil sands are shallow enough to be suitable for surface mining. The other 80% has to be produced by oil wells using enhanced oil recovery techniques like steam-assisted gravity drainage.
Much smaller heavy oil or bitumen deposits also occur in the Uinta Basin in Utah, US. The Tar Sand Triangle deposit, for example, is roughly 6% bitumen.
Bitumen may occur in hydrothermal veins. An example of this is within the Uinta Basin of Utah, in the US, where there is a swarm of laterally and vertically extensive veins composed of a solid hydrocarbon termed Gilsonite. These veins formed by the polymerization and solidification of hydrocarbons that were mobilized from the deeper oil shales of the Green River Formation during burial and diagenesis.
Bitumen is similar to the organic matter in carbonaceous meteorites. However, detailed studies have shown these materials to be distinct. The vast Alberta bitumen resources are considered to have started out as living material from marine plants and animals, mainly algae, that died millions of years ago when an ancient ocean covered Alberta. They were covered by mud, buried deeply over time, and gently cooked into oil by geothermal heat at a temperature of 50 to 150 °C (120 to 300 °F). Due to pressure from the rising of the Rocky Mountains in southwestern Alberta, 80 to 55 million years ago, the oil was driven northeast hundreds of kilometres and trapped into underground sand deposits left behind by ancient river beds and ocean beaches, thus forming the oil sands.
The use of natural bitumen for waterproofing, and as an adhesive dates at least to the fifth millennium BC, with a crop storage basket discovered in Mehrgarh, of the Indus Valley Civilization, lined with it. By the 3rd millennia BC refined rock asphalt was in use, in the region, and was used to waterproof the Great Bath, Mohenjo-daro.
In the ancient Middle East, the Sumerians used natural bitumen deposits for mortar between bricks and stones, to cement parts of carvings, such as eyes, into place, for ship caulking, and for waterproofing. The Greek historian Herodotus said hot bitumen was used as mortar in the walls of Babylon.
The 1 kilometre (0.62 mi) long Euphrates Tunnel beneath the river Euphrates at Babylon in the time of Queen Semiramis (ca. 800 BC) was reportedly constructed of burnt bricks covered with bitumen as a waterproofing agent.
Bitumen was used by ancient Egyptians to embalm mummies. The Persian word for asphalt is moom, which is related to the English word mummy. The Egyptians’ primary source of bitumen was the Dead Sea, which the Romans knew as Palus Asphaltites (Asphalt Lake).
Approximately 40 AD, Dioscorides described the Dead Sea material as Judaicum bitumen, and noted other places in the region where it could be found. The Sidon bitumen is thought to refer to material found at Hasbeya. Pliny refers also to bitumen being found in Epirus. It was a valuable strategic resource, the object of the first known battle for a hydrocarbon deposit—between the Seleucids and the Nabateans in 312 BC.
In the ancient Far East, natural bitumen was slowly boiled to get rid of the higher fractions, leaving a thermoplastic material of higher molecular weight that when layered on objects became quite hard upon cooling. This was used to cover objects that needed waterproofing, such as scabbards and other items. Statuettes of household deities were also cast with this type of material in Japan, and probably also in China.
In North America, archaeological recovery has indicated bitumen was sometimes used to adhere stone projectile points to wooden shafts. In Canada, aboriginal people used bitumen seeping out of the banks of the Athabasca and other rivers to waterproof birch bark canoes, and also heated it in smudge pots to ward off mosquitoes in the summer.
In 1553, Pierre Belon described in his work Observations that pissasphalto, a mixture of pitch and bitumen, was used in the Republic of Ragusa (now Dubrovnik, Croatia) for tarring of ships.
An 1838 edition of Mechanics Magazine cites an early use of asphalt in France. A pamphlet dated 1621, by “a certain Monsieur d’Eyrinys, states that he had discovered the existence (of asphaltum) in large quantities in the vicinity of Neufchatel”, and that he proposed to use it in a variety of ways – “principally in the construction of air-proof granaries, and in protecting, by means of the arches, the water-courses in the city of Paris from the intrusion of dirt and filth”, which at that time made the water unusable. “He expatiates also on the excellence of this material for forming level and durable terraces” in palaces, “the notion of forming such terraces in the streets not one likely to cross the brain of a Parisian of that generation”.
But the substance was generally neglected in France until the revolution of 1830. In the 1830s there was a surge of interest, and asphalt became widely used “for pavements, flat roofs, and the lining of cisterns, and in England, some use of it had been made of it for similar purposes”. Its rise in Europe was “a sudden phenomenon”, after natural deposits were found “in France at Osbann (Bas-Rhin), the Parc (Ain) and the Puy-de-la-Poix (Puy-de-Dôme)”, although it could also be made artificially. One of the earliest uses in France was the laying of about 24,000 square yards of Seyssel asphalt at the Place de la Concorde in 1835.
Among the earlier uses of bitumen in the United Kingdom was for etching. William Salmon’s Polygraphice (1673) provides a recipe for varnish used in etching, consisting of three ounces of virgin wax, two ounces of mastic, and one ounce of asphaltum. By the fifth edition in 1685, he had included more asphaltum recipes from other sources.
The first British patent for the use of asphalt was “Cassell’s patent asphalte or bitumen” in 1834. Then on 25 November 1837, Richard Tappin Claridge patented the use of Seyssel asphalt (patent #7849), for use in asphalte pavement, having seen it employed in France and Belgium when visiting with Frederick Walter Simms, who worked with him on the introduction of asphalt to Britain. Dr T. Lamb Phipson writes that his father, Samuel Ryland Phipson, a friend of Claridge, was also “instrumental in introducing the asphalte pavement (in 1836)”. Indeed, mastic pavements had been previously employed at Vauxhall by a competitor of Claridge, but without success.
Claridge obtained a patent in Scotland on 27 March 1838, and obtained a patent in Ireland on 23 April 1838. In 1851, extensions for the 1837 patent and for both 1838 patents were sought by the trustees of a company previously formed by Claridge. Claridge’s Patent Asphalte Company—formed in 1838 for the purpose of introducing to Britain “Asphalte in its natural state from the mine at Pyrimont Seysell in France”,—”laid one of the first asphalt pavements in Whitehall”. Trials were made of the pavement in 1838 on the footway in Whitehall, the stable at Knightsbridge Barracks,”and subsequently on the space at the bottom of the steps leading from Waterloo Place to St. James Park”. “The formation in 1838 of Claridge’s Patent Asphalte Company (with a distinguished list of aristocratic patrons, and Marc and Isambard Brunel as, respectively, a trustee and consulting engineer), gave an enormous impetus to the development of a British asphalt industry”. “By the end of 1838, at least two other companies, Robinson’s and the Bastenne company, were in production”, with asphalt being laid as paving at Brighton, Herne Bay, Canterbury, Kensington, the Strand, and a large floor area in Bunhill-row, while meantime Claridge’s Whitehall paving “continue(d) in good order”.
Residential Asphalt Driveway Contractors in Bryanston ?(Redirected from Asphalt pavement) A road being resurfaced
A road surface or pavement is the durable surface material laid down on an area intended to sustain vehicular or foot traffic, such as a road or walkway. In the past, gravel road surfaces, cobblestone and granite setts were extensively used, but these surfaces have mostly been replaced by asphalt or concrete laid on a compacted base course. Road surfaces are frequently marked to guide traffic. Today, permeable paving methods are beginning to be used for low-impact roadways and walkways. Pavements are crucial to countries such as US and Canada, which heavily depend on road transportation. Therefore, research projects such as Long-Term Pavement Performance are launched to optimize the life-cycle of different road surfaces.Red surfacing for the bicycle lane in the Netherlands Closeup of asphalt on a driveway
Asphalt (specifically, asphalt concrete), sometimes called flexible pavement due to the nature in which it distributes loads, has been widely used since the 1920s. The viscous nature of the bitumen binder allows asphalt concrete to sustain significant plastic deformation, although fatigue from repeated loading over time is the most common failure mechanism. Most asphalt surfaces are laid on a gravel base, which is generally at least as thick as the asphalt layer, although some 'full depth' asphalt surfaces are laid directly on the native subgrade. In areas with very soft or expansive subgrades such as clay or peat, thick gravel bases or stabilization of the subgrade with Portland cement or lime may be required. Polypropylene and polyester geosynthetics have also been used for this purpose and in some northern countries, a layer of polystyrene boards have been used to delay and minimize frost penetration into the subgrade.
Depending on the temperature at which it is applied, asphalt is categorized as hot mix, warm mix, or cold mix. Hot mix asphalt is applied at temperatures over 300 °F (150 °C) with a free floating screed. Warm mix asphalt is applied at temperatures of 200–250 °F (95–120 °C), resulting in reduced energy usage and emissions of volatile organic compounds. Cold mix asphalt is often used on lower-volume rural roads, where hot mix asphalt would cool too much on the long trip from the asphalt plant to the construction site.
An asphalt concrete surface will generally be constructed for high-volume primary highways having an average annual daily traffic load greater than 1200 vehicles per day. Advantages of asphalt roadways include relatively low noise, relatively low cost compared with other paving methods, and perceived ease of repair. Disadvantages include less durability than other paving methods, less tensile strength than concrete, the tendency to become slick and soft in hot weather and a certain amount of hydrocarbon pollution to soil and groundwater or waterways.
In the mid-1960s, rubberized asphalt was used for the first time, mixing crumb rubber from used tires with asphalt. While a potential use for tires that would otherwise fill landfills and present a fire hazard, rubberized asphalt has shown greater incidence of wear in freeze-thaw cycles in temperate zones due to non-homogeneous expansion and contraction with non-rubber components. The application of rubberized asphalt is more temperature-sensitive, and in many locations can only be applied at certain times of the year.
Study results of the long-term acoustic benefits of rubberized asphalt are inconclusive. Initial application of rubberized asphalt may provide 3–5 decibels (dB) reduction in tire-pavement source noise emissions; however, this translates to only 1–3 decibels (dB) in total traffic noise level reduction (due to the other components of traffic noise). Compared to traditional passive attenuating measures (e.g., noise walls and earth berms), rubberized asphalt provides shorter-lasting and lesser acoustic benefits at typically much greater expense.Concrete roadway in San Jose, California Further information: Concrete
Concrete surfaces (specifically, Portland cement concrete) are created using a concrete mix of Portland cement, coarse aggregate, sand and water. In virtually all modern mixes there will also be various admixtures added to increase workability, reduce the required amount of water, mitigate harmful chemical reactions and for other beneficial purposes. In many cases there will also be Portland cement substitutes added, such as fly ash. This can reduce the cost of the concrete and improve its physical properties. The material is applied in a freshly mixed slurry, and worked mechanically to compact the interior and force some of the cement slurry to the surface to produce a smoother, denser surface free from honeycombing. The water allows the mix to combine molecularly in a chemical reaction called hydration.A concrete road in Ewing, New Jersey. The original pavement was laid in the 1950s and has not been significantly altered since.
Concrete surfaces have been refined into three common types: jointed plain (JPCP), jointed reinforced (JRCP) and continuously reinforced (CRCP). The one item that distinguishes each type is the jointing system used to control crack development.
One of the major advantages of concrete pavements is they are typically stronger and more durable than asphalt roadways. They also can be grooved to provide a durable skid-resistant surface. A notable disadvantage is that they typically can have a higher initial cost, and can be more time-consuming to construct. This cost can typically be offset through the long life cycle of the pavement. Concrete pavement can be maintained over time utilizing a series of methods known as concrete pavement restoration which include diamond grinding, dowel bar retrofits, joint and crack sealing, cross-stitching, etc. Diamond grinding is also useful in reducing noise and restoring skid resistance in older concrete pavement.
The first street in the United States to be paved with concrete was Court Avenue in Bellefontaine, Ohio in 1893. The first mile of concrete pavement in the United States was on Woodward Avenue in Detroit, Michigan in 1909. Following these pioneering uses, the Lincoln Highway Association, established in October 1913 to oversee the creation of one of the United States' earliest east-west transcontinental highways for the then-new automobile, began to establish "seedling miles" of specifically concrete-paved roadbed in various places in the American Midwest, starting in 1914 west of Malta, Illinois, while using concrete with the specified concrete "ideal section" for the Lincoln Highway in Lake County, Indiana during 1922 and 1923.An example of composite pavement: hot-mix asphalt overlaid onto Portland cement concrete pavement
Composite pavements combine a Portland cement concrete sublayer with an asphalt. They are usually used to rehabilitate existing roadways rather than in new construction.
Asphalt overlays are sometimes laid over distressed concrete to restore a smooth wearing surface. A disadvantage of this method is that movement in the joints between the underlying concrete slabs, whether from thermal expansion and contraction, or from deflection of the concrete slabs from truck axle loads, usually causes reflective cracks in the asphalt. To decrease reflective cracking, concrete pavement is broken apart through a break and seat, crack and seat, or rubblization process. Geosynthetics can be used for reflective crack control. With break and seat and crack and seat processes, a heavy weight is dropped on the concrete to induce cracking, then a heavy roller is used to seat the resultant pieces into the subbase. The main difference between the two processes is the equipment used to break the concrete pavement and the size of the resulting pieces. The theory is frequent small cracks will spread thermal stress over a wider area than infrequent large joints, reducing the stress on the overlying asphalt pavement. Rubblization is a more complete fracturing of the old, worn-out concrete, effectively converting the old pavement into an aggregate base for a new asphalt road.
Whitetopping uses Portland cement concrete to resurface a distressed asphalt road.An asphalt milling machine in Boise, Idaho.
Distressed road materials can be reused when rehabilitating a roadway. The existing pavement is ground or broken up into small pieces, through a process called milling. It can then be transported to an asphalt or concrete plant and incorporated into new pavement, or recycled in place to form the base or subbase for new pavement. Some methods used include:Main article: Chipseal
Bituminous surface treatment (BST) or chipseal is used mainly on low-traffic roads, but also as a sealing coat to rejuvenate an asphalt concrete pavement. It generally consists of aggregate spread over a sprayed-on asphalt emulsion or cut-back asphalt cement. The aggregate is then embedded into the asphalt by rolling it, typically with a rubber-tired roller. This type of surface is described by a wide variety of regional terms including "chip seal", "tar and chip", "oil and stone", "seal coat", "sprayed seal" or "surface dressing" or as simply "bitumen."
BST is used on hundreds of miles of the Alaska Highway and other similar roadways in Alaska, the Yukon Territory, and northern British Columbia. The ease of application of BST is one reason for its popularity, but another is its flexibility, which is important when roadways are laid down over unstable terrain that thaws and softens in the spring.
Other types of BSTs include micropaving, slurry seals and Novachip. These are laid down using specialized and proprietary equipment. They are most often used in urban areas where the roughness and loose stone associated with chip seals is considered undesirable.
A thin membrane surface (TMS) is an oil-treated aggregate which is laid down upon a gravel road bed, producing a dust-free road. A TMS road reduces mud problems and provides stone-free roads for local residents where loaded truck traffic is negligible. The TMS layer adds no significant structural strength, and so is used on secondary highways with low traffic volume and minimal weight loading. Construction involves minimal subgrade preparation, following by covering with a 50-to-100-millimetre (2.0–3.9 in) cold mix asphalt aggregate. The Operation Division of the Ministry of Highways and Infrastructure in Saskatchewan has the responsibility of maintaining 6,102 kilometres (3,792 mi) of thin membrane surface (TMS) highways.
Otta seal is a low-cost road surface using a 16–30-millimetre (0.63–1.18 in) thick mixture of bitumen and crushed rock.Main article: Gravel road
Gravel is known to have been used extensively in the construction of roads by soldiers of the Roman Empire (see Roman road) but in 1998 a limestone-surfaced road, thought to date back to the Bronze Age, was found at Yarnton in Oxfordshire, Britain. Applying gravel, or "metalling," has had two distinct usages in road surfacing. The term road metal refers to the broken stone or cinders used in the construction or repair of roads or railways, and is derived from the Latin metallum, which means both "mine" and "quarry". The term originally referred to the process of creating a gravel roadway. The route of the roadway would first be dug down several feet and, depending on local conditions, French drains may or may not have been added. Next, large stones were placed and compacted, followed by successive layers of smaller stones, until the road surface was composed of small stones compacted into a hard, durable surface. "Road metal" later became the name of stone chippings mixed with tar to form the road surfacing material tarmac. A road of such material is called a "metalled road" in Britain, a "paved road" in Canada and the US, or a "sealed road" in parts of Canada, Australia and New Zealand.
A granular surface can be used with a traffic volume where the annual average daily traffic is 1,200 vehicles per day or less. There is some structural strength if the road surface combines a sub base and base and is topped with a double graded seal aggregate with emulsion. Besides the 4,929 kilometres (3,063 mi) of granular pavements maintained in Saskatchewan, around 40% of New Zealand roads are unbound granular pavement structures.
The decision whether to pave a gravel road or not often hinges on traffic volume. It has been found that maintenance costs for gravel roads often exceed the maintenance costs for paved or surface-treated roads when traffic volumes exceed 200 vehicles per day.
Some communities are finding it makes sense to convert their low-volume paved roads to aggregate surfaces.
Pavers (or paviours), generally in the form of pre-cast concrete blocks, are often used for aesthetic purposes, or sometimes at port facilities that see long-duration pavement loading. Pavers are rarely used in areas that see high-speed vehicle traffic.
Brick, cobblestone, sett, wood plank, and wood block pavements such as Nicolson pavement, were once common in urban areas throughout the world, but fell out of fashion in most countries, due to the high cost of labor required to lay and maintain them, and are typically only kept for historical or aesthetic reasons. In some countries, however, they are still common in local streets. In the Netherlands, brick paving has made something of a comeback since the adoption of a major nationwide traffic safety program in 1997. From 1998 through 2007, more than 41,000 km of city streets were converted to local access roads with a speed limit of 30 km/h, for the purpose of traffic calming. One popular measure is to use brick paving - the noise and vibration slows motorists down. At the same time, it is not uncommon for cycle paths alongside a road to have a smoother surface than the road itself.
Likewise, macadam and tarmac pavements can still sometimes[when?] be found buried underneath asphalt concrete or Portland cement concrete pavements, but are rarely[clarification needed] constructed today[when?].
There are also other methods and materials to create pavements that have appearance of brick pavements. The first method to create brick texture is to heat an asphalt pavement and use metal wires to imprint a brick pattern using a compactor to create stamped asphalt. A similar method is to use rubber imprinting tools to press over a thin layer of cement to create decorative concrete. Another method is to use a brick pattern stencil and apply a surfacing material over the stencil. Materials that can be applied to give the color of the brick and skid resistance can be in many forms. An example is to use colored polymer-modified concrete slurry which can be applied by screeding or spraying. Another material is aggregate-reinforced thermoplastic which can be heat applied to the top layer of the brick-pattern surface. Other coating materials over stamped asphalt are paints and two-part epoxy coating.
Roadway surfacing choices are known to affect the intensity and spectrum of sound emanating from the tire/surface interaction. Initial applications of noise studies occurred in the early 1970s. Noise phenomena are highly influenced by vehicle speed.
Roadway surface types contribute differential noise effects of up to 4 dB, with chip seal type and grooved roads being the loudest, and concrete surfaces without spacers being the quietest. Asphaltic surfaces perform intermediately relative to concrete and chip seal. Rubberized asphalt has been shown to give a marginal 3–5 dB reduction in tire-pavement noise emissions, and a marginally discernible 1–3 dB reduction in total road noise emissions when compared to conventional asphalt applications.See also: Pothole, Crocodile cracking, Rut (roads), and Bleeding (roads) Deteriorating asphalt
As pavement systems primarily fail due to fatigue (in a manner similar to metals), the damage done to pavement increases with the fourth power of the axle load of the vehicles traveling on it. According to the AASHO Road Test, heavily loaded trucks can do more than 10,000 times the damage done by a normal passenger car. Tax rates for trucks are higher than those for cars in most countries for this reason, though they are not levied in proportion to the damage done. Passenger cars are considered to have little practical effect on a pavement's service life, from a materials fatigue perspective.
Other failure modes include aging and surface abrasion. As years go by, the binder in a bituminous wearing course gets stiffer and less flexible. When it gets "old" enough, the surface will start losing aggregates, and macrotexture depth increases dramatically. If no maintenance action is done quickly on the wearing course, potholes will form. The freeze-thaw cycle in cold climates will dramatically accelerate pavement deterioration, once water can penetrate the surface.
If the road is still structurally sound, a bituminous surface treatment, such as a chipseal or surface dressing can prolong the life of the road at low cost. In areas with cold climate, studded tires may be allowed on passenger cars. In Sweden and Finland, studded passenger car tires account for a very large share of pavement rutting.
The physical properties of a stretch of pavement can be tested using a falling weight deflectometer.
Several design methods have been developed to determine the thickness and composition of road surfaces required to carry predicted traffic loads for a given period of time. Pavement design methods are continuously evolving. Among these are the Shell Pavement design method, and the American Association of State Highway and Transportation Officials (AASHTO) 1993 "Guide for Design of Pavement Structures". A new mechanistic-empirical design guide has been under development by NCHRP (Called Superpave Technology) since 1998. A new design guide called Mechanistic Empirical Pavement Design Guide (MEPDG) was developed and is about to be adopted by AASHTO.
Further research by University College London into pavements has led to the development of an indoor, 80-sq-metre artificial pavement at a research centre called Pedestrian Accessibility and Movement Environment Laboratory (PAMELA). It is used to simulate everyday scenarios, from different pavement users to varying pavement conditions. There also exists a research facility near Auburn University, the NCAT Pavement Test Track, that is used to test experimental asphalt pavements for durability.
In addition to repair costs, the condition of a road surface has economic effects for road users. Rolling resistance increases on rough pavement, as does wear and tear of vehicle components. It has been estimated that poor road surfaces cost the average US driver $324 per year in vehicle repairs, or a total of $67 billion. Also, it has been estimated that small improvements in road surface conditions can decrease fuel consumption between 1.8 and 4.7%.Main article: Road surface marking
Road surface markings are used on paved roadways to provide guidance and information to drivers and pedestrians. It can be in the form of mechanical markers such as cat's eyes, botts' dots and rumble strips, or non-mechanical markers such as paints, thermoplastic, plastic and epoxy.
Diverging diamond interchangePermeable paving demonstration Stone paving in Santarém, Portugal
Permeable paving is a method of paving vehicle and pedestrian pathways that allows for infiltration of fluids. In pavement design the base is the top portion of the roadway that pedestrians or vehicles come into contact with. The media used for the base of permeable paving may be porous to allow for fluids to flow through it or nonporous media that are spaced so that fluid may flow in between the crack may be used. In addition to reducing surface runoff, permeable paving can trap suspended solids therefore filtering pollutants from stormwater. Examples include roads, paths, and parking lots that are subject to light vehicular traffic, such as cycle-paths, service or emergency access lanes, road and airport shoulders, and residential sidewalks and driveways.
Although some porous paving materials appear nearly indistinguishable from nonporous materials, their environmental effects are qualitatively different. Whether it is pervious concrete, porous asphalt, paving stones or concrete or plastic-based pavers, all these pervious materials allow stormwater to percolate and infiltrate the surface areas, traditionally impervious to the soil below. The goal is to control stormwater at the source, reduce runoff and improve water quality by filtering pollutants in the substrata layers.
Permeable solutions can be based on: porous asphalt and concrete surfaces, concrete pavers (permeable interlocking concrete paving systems – PICP), or polymer-based grass pavers, grids and geocells. Porous pavements and concrete pavers (actually the voids in-between them) enable stormwater to drain through a stone base layer for on-site infiltration and filtering. Polymer based grass grid or cellular paver systems provide load bearing reinforcement for unpaved surfaces of gravel or turf.
Grass pavers, plastic turf reinforcing grids (PTRG), and geocells (cellular confinement systems) are honeycombed 3D grid-cellular systems, made of thin-walled HDPE plastic or other polymer alloys. These provide grass reinforcement, ground stabilization and gravel retention. The 3D structure reinforces infill and transfers vertical loads from the surface, distributing them over a wider area. Selection of the type of cellular grid depends to an extent on the surface material, traffic and loads. The cellular grids are installed on a prepared base layer of open-graded stone (higher void spacing) or engineered stone (stronger). The surface layer may be compacted gravel or topsoil seeded with grass and fertilizer. In addition to load support, the cellular grid reduces compaction of the soil to maintain permeability, while the roots improve permeability due to their root channels.
In new suburban growth, porous pavements protect watersheds. In existing built-up areas and towns, redevelopment and reconstruction are opportunities to implement stormwater water management practices. Permeable paving is an important component in Low Impact Development (LID), a process for land development in the United States that attempts to minimize impacts on water quality and the similar concept of sustainable drainage systems (SuDS) in the United Kingdom.
The infiltration capacity of the native soil is a key design consideration for determining the depth of base rock for stormwater storage or for whether an underdrain system is needed.
Permeable paving surfaces have been demonstrated as effective in managing runoff from paved surfaces. Large volumes of urban runoff causes serious erosion and siltation in surface water bodies. Permeable pavers provide a solid ground surface, strong enough to take heavy loads, like large vehicles, while at the same time they allow water to filter through the surface and reach the underlying soils, mimicking natural ground absorption. They can reduce downstream flooding and stream bank erosion, and maintain base flows in rivers to keep ecosystems self-sustaining. Permeable pavers also combat erosion that occurs when grass is dry or dead, by replacing grassed areas in suburban and residential environments.
Permeable paving surfaces keep the pollutants in place in the soil or other material underlying the roadway, and allow water seepage to groundwater recharge while preventing the stream erosion problems. They capture the heavy metals that fall on them, preventing them from washing downstream and accumulating inadvertently in the environment. In the void spaces, naturally occurring micro-organisms digest car oils, leaving little but carbon dioxide and water. Rainwater infiltration is usually less than that of an impervious pavement with a separate stormwater management facility somewhere downstream..in areas where infiltration is not possible due to unsuitable soil conditions permeable pavements are used in the attenuation mode where water is retained in the pavement and slowly released to surface water systems between storm events.
Permeable pavements may give urban trees the rooting space they need to grow to full size. A "structural-soil" pavement base combines structural aggregate with soil; a porous surface admits vital air and water to the rooting zone. This integrates healthy ecology and thriving cities, with the living tree canopy above, the city's traffic on the ground, and living tree roots below. The benefits of permeables on urban tree growth have not been conclusively demonstrated and many researchers have observed tree growth is not increased if construction practices compact materials before permeable pavements are installed.
Permeable pavements are designed to replace Effective Impervious Areas (EIAs), not to manage stormwater from other impervious surfaces on site. Use of this technique must be part of an overall on site management system for stormwater, and is not a replacement for other techniques.
Also, in a large storm event, the water table below the porous pavement can rise to a higher level preventing the precipitation from being absorbed into the ground. The additional water is stored in the open graded crushed drain rock base and remains until the subgrade can absorb the water. For clay-based soils, or other low to 'non'-draining soils, it is important to increase the depth of the crushed drain rock base to allow additional capacity for the water as it waits to be infiltrated.
The best way to prevent this problem is to understand the soil infiltration rate, and design the pavement and base depths to meet the volume of water. Or, allow for adequate rain water run off at the pavement design stage.
Highly contaminated runoff can be generated by some land uses where pollutant concentrations exceed those typically found in stormwater. These "hot spots" include commercial plant nurseries, recycling facilities, fueling stations, industrial storage, marinas, some outdoor loading facilities, public works yards, hazardous materials generators (if containers are exposed to rainfall), vehicle service and maintenance areas, and vehicle and equipment washing and steam cleaning facilities. Since porous pavement is an infiltration practice, it should not be applied at stormwater hot spots due to the potential for groundwater contamination. All contaminated runoff should be prevented from entering municipal storm drain systems by using best management practices (BMPs) for the specific industry or activity.
Reference sources differ on whether low or medium traffic volumes and weights are appropriate for porous pavements. For example, around truck loading docks and areas of high commercial traffic, porous pavement is sometimes cited as being inappropriate. However, given the variability of products available, the growing number of existing installations in North America and targeted research by both manufacturers and user agencies, the range of accepted applications seems to be expanding. Some concrete paver companies have developed products specifically for industrial applications. Working examples exist at fire halls, busy retail complex parking lots, and on public and private roads, including intersections in parts of North America with quite severe winter conditions.
Permeable pavements may not be appropriate when land surrounding or draining into the pavement exceeds a 20 percent slope, where pavement is down slope from buildings or where foundations have piped drainage at their footers. The key is to ensure that drainage from other parts of a site is intercepted and dealt with separately rather than being directed onto permeable surfaces.
Cold climates may present special challenges. Road salt contains chlorides that could migrate through the porous pavement into groundwater. Snow plow blades could catch block edges and damage surfaces. Sand cannot be used for snow and ice control on perveous asphalt or concrete because it will plug the pores and reduce permeability. Infiltrating runoff may freeze below the pavement, causing frost heave, though design modifications can reduce this risk. These potential problems do not mean that porous pavement cannot be used in cold climates. Porous pavement designed to reduce frost heave has been used successfully in Norway. Furthermore, experience suggests that rapid drainage below porous surfaces increases the rate of snow melt above.
Some estimates put the cost of permeable paving at two to three times that of conventional asphalt paving. Using permeable paving, however, can reduce the cost of providing larger or more stormwater BMPs on site, and these savings should be factored into any cost analysis. In addition, the off-site environmental impact costs of not reducing on-site stormwater volumes and pollution have historically been ignored or assigned to other groups (local government parks, public works and environmental restoration budgets, fisheries losses, etc.) The City of Olympia, Washington is studying the use of pervious concrete quite closely and finding that new stormwater regulations are making it a viable alternative to storm water.
Some permeable pavements require frequent maintenance because grit or gravel can block the open pores. This is commonly done by industrial vacuums that suck up all the sediment. If maintenance is not carried out on a regular basis, the porous pavements can begin to function more like impervious surfaces. With more advanced paving systems the levels of maintenance needed can be greatly decreased, elastomerically bound glass pavements requires less maintenance than regular concrete paving as the glass bound pavement has 50% more void space.
Plastic grid systems, if selected and installed correctly, are becoming more and more popular with local government maintenance personnel owing to the reduction in maintenance efforts: reduced gravel migration and weed suppression in public park settings.
Some permeable paving products are prone to damage from misuse, such as drivers who tear up patches of plastic & gravel grid systems by "joy riding" on remote parking lots at night. The damage is not difficult to repair but can look unsightly in the meantime. Grass pavers require supplemental watering in the first year to establish the vegetation, otherwise they may need to be re-seeded. Regional climate also means that most grass applications will go dormant during the dry season. While brown vegetation is only a matter of aesthetics, it can influence public support for this type of permeable paving.
Traditional permeable concrete paving bricks tend to lose their color in relatively short time which can be costly to replace or clean and is mainly due to the problem of efflorescence.
Efflorescence is a hardened crystalline deposit of salts, which migrate from the center of concrete or masonry pavers to the surface to form insoluble calcium carbonates that harden on the surface. Given time, these deposits form much like how a stalactite takes shape in a cave, except in this case on a flat surface. Efflorescence usually appears white, gray or black depending on the region.
Over time efflorescence begins to negatively affect the overall appearance of masonry/concrete and may cause the surfaces to become slippery when exposed to moisture. If left unchecked, this efflorescence will harden whereby the calcium/lime deposits begin to affect the integrity of the cementatious surface by slowly eroding away the cement paste and aggregate. In some cases it will also discolor stained or coated surfaces.
Efflorescence forms more quickly in areas that are exposed to excessive amounts of moisture such as near pool decks, spas, and fountains or where irrigation runoff is present. As a result, these affected regions become very slick when wet thereby causing a significant loss of "friction coefficient". This can be of serious concern especially as a public safety issue to individuals, principals and property owners by exposing them to possible injury and increased general liability claims.
Efflorescence remover chemicals can be used to remove calcium/lime build-up without damaging the integrity of the paving surface.
Installation of porous pavements is no more difficult than that of dense pavements, but has different specifications and procedures which must be strictly adhered to. Nine different families of porous paving materials present distinctive advantages and disadvantages for specific applications. Here are examples:Main article: Pervious concrete
Pervious concrete is widely available, can bear frequent traffic, and is universally accessible. Pervious concrete quality depends on the installer's knowledge and experience.
Plastic grids allow for a 100% porous system using structural grid systems for containing and stabilizing either gravel or turf. These grids come in a variety of shapes and sizes depending on use; from pathways to commercial parking lots. These systems have been used readily in Europe for over a decade, but are gaining popularity in North America due to requirements by government for many projects to meet LEED environmental building standards. Plastic grid system are also popular with homeowners due to their lower cost to install, ease of installation, and versatility. The ideal design for this type of grid system is a closed cell system, which prevents gravel/sand/turf from migrating laterally. It is also known as Grass pavers / Turf Pavers in India 
Porous asphalt is produced and placed using the same methods as conventional asphalt concrete; it differs in that fine (small) aggregates are omitted from the asphalt mixture. The remaining large, single-sized aggregate particles leave open voids that give the material its porosity and permeability. To ensure pavement strength, fiber may be added to the mix or a polymer-modified asphalt binder may be used. Generally, porous asphalt pavements are designed with a subsurface reservoir that holds water that passes through the pavement, allowing it to evaporate and/or percolate slowly into the surround soils.
Open-graded friction courses (OGFC) are a porous asphalt surface course used on highways to improve driving safety by removing water from the surface. Unlike a full-depth porous asphalt pavement, OGFCs do not drain water to the base of a pavement. Instead, they allow water to infiltrate the top 3/4 to 1.5 inch of the pavement and then drain out to the side of the roadway. This can improve the friction characteristics of the road and reducing road spray.
Single-sized aggregate without any binder, e.g. loose gravel, stone-chippings, is another alternative. Although it can only be safely used in very low-speed, low-traffic settings, e.g. car-parks and drives, its potential cumulative area is great.Grass pavement
Porous turf, if properly constructed, can be used for occasional parking like that at churches and stadia. Plastic turf reinforcing grids can be used to support the increased load.:2  Living turf transpires water, actively counteracting the "heat island" with what appears to be a green open lawn.Main article: interlocking concrete pavers
Permeable interlocking concrete pavements are concrete units with open, permeable spaces between the units.:2 They give an architectural appearance, and can bear both light and heavy traffic, particularly interlocking concrete pavers, excepting high-volume or high-speed roads. Some products are polymer-coated and have an entirely porous face.
Permeable clay brick pavements are fired clay brick units with open, permeable spaces between the units. Clay pavers provide a durable surface that allows stormwater runoff to permeate through the joints.Main article: Resin bound paving
Resin bound paving is a mixture of resin binder and aggregate. Clear resin is used to fully coat each aggregate particle before laying. Enough resin is used to allow each aggregate particle to adhere to one another and to the base yet leave voids for water to permeate through. Resin bound paving provides a strong and durable surface that is suitable for pedestrian and vehicular traffic in applications such as pathways, driveways, car parks and access roads.
Elastomerically bound recycled glass porous pavement consisting of bonding processed post consumer glass with a mixture of resins, pigments, granite and binding agents. Approximately 75 percent of glass in the U.S. is disposed in landfills.
Stormwater management practices related to roadways: