Parking Lot Resurfacing Fourways

One of the most affordable and convenient methods for small-scale asphalt mending projects is to use a cold patch mix. Many property owners will tell you that this approach saves money, Parking Lot Resurfacing in Fourways and can reduce the amount of labor required for the job, making it a great solution for small holes in parking lots, walkways, streets, and driveways. However, the process of cold asphalt patching can be accelerated with the right application techniques, saving property owners some time too! Customers, clients, guests, and occupants can use the pavement in the same day!

Continue reading to learn some great tips on how you can shorten the amount of time it takes for the cold patch asphalt mix to harden, and drastically cut down on turnaround time, from project start to finish.

Paving Services Price

Ease of Use

The primary reason why this product is the go-to choice for small hole repairs in asphalt pavements is the ease of installation. There is no long, extended process of preparing or mixing materials. Instead, the air does most of the work. You simply pour the mix directly into the hole, compact it with simple manual tools (metal tamper or piece of lumber), and leave it to air dry. The mix turns into a permanent surface patch after extended contact with air.

The drying process, also known as curing, is very important to establishing a solid, stable surface that lasts a long time. If you want a permanent repair for your asphalt, you need to make sure the entire process is done correctly. If you want to speed up the curing stage of your pavement repair project, you can try a few recommended tips.

Paving Services Near Me

Use Gravel

You can use gravel to create a more dense space within the hole, which may help to establish lasting strength. Just fill the hole with gravel, little by little, while using your compacting tools to compress the gravel with each layer. Do not fill the hole all the way to the top; be sure to leave 2 inches of space below the surface line for your cold patch mix.

Pouring Your Mix

As you pour your mix, exceed the surface line by half an inch. This means that your mix should go over the top of the hole by a ½ inch. Then use your compacting tools to compress your material down until it is properly flattened. You may need to repeat this step two or three times to get a proper fill.

Paving Companies Cost Estimate

Expedited Drying

Asphalt cold patch mix cures by having contact with air. You can speed up the drying process by using hair dryers or commercial paint dryers. If you are going to use a hair dryer, you will need to manually operate it in a steady, sweeping motion to ensure even curing. The material is near dry when you cannot easily press into the surface with your hand.

Large-Scale Pavement Repair

For large-scale pavement repair jobs, you need a professional paving company. They have the training, equipment, and resources to provide dependable work in a convenient time frame. Be sure to choose a company that is licensed, bonded, and insured, and retains decades of experience in the road construction industry.

Parking Lot Resurfacing in Fourways ?

Residential Paving Companies Near Me

Many people think the since you drive your car on both your asphalt driveway the concrete slab in your garage that they should both be sealed with the same product. This is absolutely false. Concrete and asphalt are diametrically opposed materials and should be treated completely differently. What works for one will not work for the other.

A sealer on asphalt actually performs two functions. First, it makes the surface look great as it tends to add back the black color and also makes it cleaner looking. Second, it protects the aggregate from loosening do to degradation of the asphalt base. Both of these benefits are important.

Wear ability studies have indicated that the best asphalt sealer should be made from coal tar instead of liquid petroleum asphalt. This seems counterintuitive but it is true. Coal tar is a byproduct of the manufacture of coke for steel manufacturing. Coke is produced from raw coal and during its formation a liquid byproduct is formed. This liquid is very sticky and cures to a very good protective surface when spread out on a roadway or driveway of asphalt.

One thing to consider with these types of sealers is that they should not be used in doors. Coal tar has volatile organic compounds which gas off during the curing process. These have been proven to be a health risk. Also, the coal tar does not bond well with concrete so another product needs to be used for your garage slab.

The best sealer for concrete is an epoxy floor coating. Epoxies cure to a very hard and tough surface which will protect your floor surface from damage and wear. They can also be tinted so your floor can match the color of your home or you can use a complementary color to your pride and joy car.

The main key for success with an epoxy garage floor coating is preparation of the concrete surface. Any petroleum based products that have stained the floor need to be completely cleaned with a degreaser before application. If you don't, the epoxy can not bond and will lift within a very short time. To see if the floor is completely cleaned use the water bead test. Spray a light coating of water on the surface and see if it beads up. Where ever it does you have a contamination problem which must be removed.

Epoxy does not work on asphalt surfaces because of the inherent plasticity even after the asphalt is cured. This slight movement cracks the epoxy and allows it to lift off the surface.

Explaining Tire Scuff Marks on New Asphalt Pavement

Asphalt Paving Companies Near Me

You're looking at your asphalt driveway and it appears to be in rough shape. What should you do? Will some repair work do the trick? Should the driveway be resurfaced, or does the whole thing need to be ripped up and redone from scratch?

Perhaps the best thing to do is to consult a few asphalt paving contractors and get their opinions, and (often free) estimates. This article can give you a general idea of what's going on, what to look for in an asphalt paving contractor, and what to include in your contract.

Maintenance is good medicine, but it's not foolproof

Asphalt driveways don't remain smooth and black forever. You can take steps to maintain your driveway by sealing and protecting it, but often the effects of heat, ultra-violet rays, and substances such as salt, oil, gas and grease take their toll. And if those don't get you, then cracking and water penetration eventually will.

Your driveway may be corroded, worn out, or have cracks, which could all warrant a resurfacing job if the condition is severe enough. As a general guide, if repairs are needed on more than 25 percent of the surface, it is more cost-effective to do a hot mix asphalt resurfacing job over the entire driveway.

Say no to cracks!

Asphalt pavement is hard and brittle, and as a result, cracks will develop over time. Ranging from hairline to an inch wide or more, cracks are your driveway's worst enemy because they let water in. In colder climates, freeze-thaw cycles can be very destructive, and can wreak havoc on your driveway if water penetrates the cracks, then expands as it turns to ice. And even in warmer climates, water penetration can cause serious damage. The larger the crack, the more serious the problem, and the sooner it needs to be fixed. Cracks that are left un-repaired will lead to serious deterioration of the pavement and even to the base layers, requiring complete replacement of the driveway - sooner rather than later in colder climates.

Can it be fixed or do you need a new driveway?

Whether you'll need to rip out your existing driveway and install a new one, or if you can get away with resurfacing - or even some patchwork and crack-filling - depends largely on the condition of the base layers, or foundation. However, if cracking covers 3/4 of the driveway, the surface is too far gone to repair. The root of the problems may come from lower down, and a complete overhaul should be considered.

If your driveway has been resurfaced several times with hot mix asphalt and keeps deteriorating prematurely, it is likely a problem with the foundation, and you should consider installing a whole new driveway. Likewise, if there are areas that have depressions or mounds, they should be completely reconstructed from the base. If you have several of these areas, a new driveway might make sense.

Various factors may cause premature wear

Although a properly installed asphalt driveway can last 15 to 20, even 25 years if properly maintained, extreme weather conditions, extra-heavy loads and shortcuts taken during construction can all cause premature wear and failure.

Beware of "traveling contractor" scams

Beware of any asphalt paving contractor who rings your doorbell and claims to have some "leftover materials" from another job, and if you agree to the work "right now," you'll get an amazing discount. If this happens to you, call the police. It is a scam. Reputable contractors calculate the materials they need very carefully, and any small amount left over from a job would never be enough to complete an entire new job. If these con artists do any work at all before taking off with your money, it will most definitely be shoddy.

Tips for hiring an asphalt paving contractor

It is best to deal with registered, bonded, adequately insured and licensed (where companies. Many reputable paving contractors also belong to trade associations, such as the National Asphalt Pavement Association (NAPA), the National Pavement Contractors Association (NPCA), or various state-specific associations.

When hiring a contractor to resurface or install a new asphalt driveway, always get a list of references and check them. Ask references about the quality of the contractor's work, their attention to details, and if the work was competed on time. You can even go and inspect previous work.

What to include in the contract

Once you decide on an Asphalt Paving Contractor, consider these points when drawing up a contract:

Clarify who is responsible for re-hanging gates or other doors, if needed, due to raised pavement levels.

Who will raise any water valves or sewer inlets to meet the asphalt around them - you, a plumber, or someone else? Who pays?

Specify that the surface must be graded to provide proper drainage.

For new installations, specify that the sub grade will be compacted before the base layer is applied.

Specify how many layers are included in the job, a description of the materials that will be used for each layer (sub-base, base and asphalt), and the thickness of each layer when compacted. Two separate layers, or lifts, of asphalt is preferred, totaling at least 3 and preferably 4 inches. Sub-base and base should be at least 6 inches each, comprised of limestone rocks with 3-to-4-inch diameter and 2-to-3-inch diameter, respectively.

Include the payment schedule and a guarantee of the finished product.

Determine whether a building permit is required, and specify that it is the contractor's responsibility to obtain one on your behalf, if needed.

Asphalt Paving Companies Near Me

https://www.helpwikileaks.co.za/sandton/

Helpwikileaks Have Driveway Sealing Companies List

 

Parking Lot Resurfacing Fourways

Parking Lot Resurfacing Fourways