One of the most affordable and convenient methods for small-scale asphalt mending projects is to use a cold patch mix. Many property owners will tell you that this approach saves money, Asphalt Driveway Installation Cost in Centurion and can reduce the amount of labor required for the job, making it a great solution for small holes in parking lots, walkways, streets, and driveways. However, the process of cold asphalt patching can be accelerated with the right application techniques, saving property owners some time too! Customers, clients, guests, and occupants can use the pavement in the same day!
Continue reading to learn some great tips on how you can shorten the amount of time it takes for the cold patch asphalt mix to harden, and drastically cut down on turnaround time, from project start to finish.
Ease of Use
The primary reason why this product is the go-to choice for small hole repairs in asphalt pavements is the ease of installation. There is no long, extended process of preparing or mixing materials. Instead, the air does most of the work. You simply pour the mix directly into the hole, compact it with simple manual tools (metal tamper or piece of lumber), and leave it to air dry. The mix turns into a permanent surface patch after extended contact with air.
The drying process, also known as curing, is very important to establishing a solid, stable surface that lasts a long time. If you want a permanent repair for your asphalt, you need to make sure the entire process is done correctly. If you want to speed up the curing stage of your pavement repair project, you can try a few recommended tips.
You can use gravel to create a more dense space within the hole, which may help to establish lasting strength. Just fill the hole with gravel, little by little, while using your compacting tools to compress the gravel with each layer. Do not fill the hole all the way to the top; be sure to leave 2 inches of space below the surface line for your cold patch mix.
Pouring Your Mix
As you pour your mix, exceed the surface line by half an inch. This means that your mix should go over the top of the hole by a ½ inch. Then use your compacting tools to compress your material down until it is properly flattened. You may need to repeat this step two or three times to get a proper fill.
Asphalt cold patch mix cures by having contact with air. You can speed up the drying process by using hair dryers or commercial paint dryers. If you are going to use a hair dryer, you will need to manually operate it in a steady, sweeping motion to ensure even curing. The material is near dry when you cannot easily press into the surface with your hand.
Large-Scale Pavement Repair
For large-scale pavement repair jobs, you need a professional paving company. They have the training, equipment, and resources to provide dependable work in a convenient time frame. Be sure to choose a company that is licensed, bonded, and insured, and retains decades of experience in the road construction industry.
Asphalt Driveway Installation Cost in Centurion ?
Many people think the since you drive your car on both your asphalt driveway the concrete slab in your garage that they should both be sealed with the same product. This is absolutely false. Concrete and asphalt are diametrically opposed materials and should be treated completely differently. What works for one will not work for the other.
A sealer on asphalt actually performs two functions. First, it makes the surface look great as it tends to add back the black color and also makes it cleaner looking. Second, it protects the aggregate from loosening do to degradation of the asphalt base. Both of these benefits are important.
Wear ability studies have indicated that the best asphalt sealer should be made from coal tar instead of liquid petroleum asphalt. This seems counterintuitive but it is true. Coal tar is a byproduct of the manufacture of coke for steel manufacturing. Coke is produced from raw coal and during its formation a liquid byproduct is formed. This liquid is very sticky and cures to a very good protective surface when spread out on a roadway or driveway of asphalt.
One thing to consider with these types of sealers is that they should not be used in doors. Coal tar has volatile organic compounds which gas off during the curing process. These have been proven to be a health risk. Also, the coal tar does not bond well with concrete so another product needs to be used for your garage slab.
The best sealer for concrete is an epoxy floor coating. Epoxies cure to a very hard and tough surface which will protect your floor surface from damage and wear. They can also be tinted so your floor can match the color of your home or you can use a complementary color to your pride and joy car.
The main key for success with an epoxy garage floor coating is preparation of the concrete surface. Any petroleum based products that have stained the floor need to be completely cleaned with a degreaser before application. If you don't, the epoxy can not bond and will lift within a very short time. To see if the floor is completely cleaned use the water bead test. Spray a light coating of water on the surface and see if it beads up. Where ever it does you have a contamination problem which must be removed.
Epoxy does not work on asphalt surfaces because of the inherent plasticity even after the asphalt is cured. This slight movement cracks the epoxy and allows it to lift off the surface.
How to Get Cold Patch Asphalt to Cure Faster
This contractor is employed by a company that makes surfaces that are paved like sidewalks, floors made of concrete, and roads. Some companies will even work on bigger projects like an airport runway. They will be hired by municipal agencies, homeowners, and business to repair existing paved surfaces or make new ones. Many of the companies that paving contractors work for will focus in either commercial or residential work but some will do both. It depends on the job and equipment needed.
Commercial paving contractors
They are the ones that will usually provide the pricing for the jobs needed in the outline of a bid. The one that is offered the job is typically the lowest bidder but not always. When working in commercial jobs, the contractor will report to the construction manager or general contractor instead of the owner. One of the jobs a paving contractor does is pour parking lots, walkways, and floors in new developments. If it is a municipal project they may repair any damage in an existing paying like cracks or potholes or lay new sidewalks, or roads,
Residential paving contractors
They will meet with the homeowner to discuss the project that is needed, figure out the approximate cost of materials and labor, and then give an estimate to the homeowner. The homeowner may hire them to put down a floor, patio, or walkway. They can also repair structures like walkways or stairs. Some of these paving companies may concentrate just on landscape paving. This can include laying stone items like outdoor tiles or pavers or installing a poured surface.
Working as a paving contractor requires being able to use big pieces of equipment, which can include:
• Paving machine to smooth the freshly laid out road or parking lot surface
• Excavator to set up the land for paving
• Tamping machines, which are large machines that are used to help flatten out the gravel or dirt surfaces
• Dump truck to haul away any excess waste products and dirt and to haul in gravel or stones
Becoming a paving contractor
If you would like to have a career working in this field, you need to be one that does not mind working outdoors in any type of weather. You also need to feel at ease working on roads that are busy since this type of work is done in the daytime when traffic is passing nearby. You may also work as a flagger so you should have experience with road safety and flagging. Working as a paving contractor, you can expect to work in conditions that are busy, noisy, and dirty. If you work with hot asphalt, you need to be aware of the different heat levels and potential toxic fumes.
Asphalt Driveway Installation Cost Centurion